Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to auto locksmiths with experience who have the proper equipment and technical know-how. They will be able to make and program new keys much faster than a dealership would and at a lesser cost.
If the key fob stopped locking or unlocking your doors, it is likely due to a dead coin battery. However, there are other reasons why the key might be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as stopping it from starting the engine. In this scenario you'll have to make use of the alternative method for starting found in your vehicle's owner's manual.
The spark plugs can also be worn out. The spark plugs ignite the fuel to start the engine. However, they have a limited life span. If they're not used enough and they fail, they'll eventually die.
There is a simple solution for this issue. Check the voltage of your battery with a multimeter. If the voltage is below 11,5 volts, it's time to replace it. If the battery is damaged it is necessary to clean its contacts. This can be done by lifting the rubber covers that protect the two terminals on the battery and using a wire brush to remove any corroded areas of the battery. Then, reconnect the cables to the positive and negative poles.
Water Damage
If your 208 does not start and the battery hasn't fallen flat, it is time to inspect the spark plugs. It could be that they are overly filthy, making them unable to spark. The spark plugs can be cleaned in the workshop.
Peugeot automobiles are equipped with a transponder that is compatible with the immobiliser. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged, then it won't send the proper signal to the vehicle.
Water damage is a typical cause of this issue. This is a typical issue in colder climates where the vehicle has been exposed to snow or rain. If this is the case, call a reputable auto locksmith who has all the tools and equipment needed to reprogram the new key. They will also have the latest technology and machinery required to create a Peugeot smart key. The process shouldn't take more than 15 minutes.
Contacts with the battery may be damaged.
Peugeot changed from the old carbon-encased transponder chips to a brand new type of chip that relies on electronic components that are placed on a circuit board. The new system is great when it's brand new, but the circuit boards deteriorate over time and cease to function properly.
This can prevent the immobiliser from activating so your vehicle won't be able to start. Contact a Peugeot specialist, or a locksmith, if this is the situation.
peugeot remote key replacement is when the battery inside the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A car locksmith can replace the battery and cut a new blade for you, this is typically a quick fix.
Faulty Receiver Module
It could be that the receiver module has a problem when your Peugeot key fob fails to function after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver is responsible for sending radio frequency signals to the on-board computer, which is responsible for controlling the centralized locking system of your Peugeot vehicle.
Rubber seals on the key fob block water from getting to the electronic chip. However, prolonged exposure to water can penetrate these seals and damage the chip. The high salt content of the ocean or pool can cause damage to the key fob if it is submerged.
The module will have to be replaced if your Peugeot spare key is no longer working. This can only by done by an Peugeot specialist or a professional auto locksmith. Peugeot keys, unlike other cars, are secured by an immobilizer system. This requires the correct coding to start the car. This is why you should be able to trust a professional Peugeot locksmith with the task of creating and programming a replacement.
Computers with faulty on-board computers
The computer on the board of your Peugeot is responsible for many of the systems within your car, ranging from power windows to the airbags. The computer on board will display an error code when something goes wrong. This code will be saved within the system until the issue is resolved. Often, this will involve replacing the computer on board.
The most typical reason for the warning light for airbags to flash is corrosion or loose connections in the sensor. This could be due to wear and tear, ageing or exposure to moisture and salt. This issue must be addressed as soon you can, since an airbag malfunctioning could be dangerous in case of an accident.
If your Peugeot is showing a card detected as not present error then the key battery in the key fob might be dead or weak. This prevents the key fob from sending a signal that disarms your vehicle's immobilizer. Test this by pressing the unlock button on the fob's key, then trying to start your car. If this does not work it is because the battery of the key must be replaced.